Avery Dennison Launches a PSA Tape Portfolio Built for Battery Energy Storage Systems
Pressure-sensitive adhesive (PSA) tapes have long been the quiet workhorses inside batteries – bonding cells, insulating busbars and sealing packs. Now Avery Dennison Performance Tapes has grouped those functions into a dedicated portfolio aimed squarely at battery energy storage systems (BESS), the grid- and commercial-scale enclosures that store energy in lithium-iron-phosphate (LFP) cells. The new lineup targets three persistent headaches in large-format storage: stopping thermal runaway from spreading, insulating high-voltage connections, and speeding up assembly without cure steps.
Why BESS is different from an EV pack
BESS units range from cabinet-sized commercial installations to shipping-container-scale sites holding thousands of cells. Inside, adhesive tapes do the unglamorous but critical jobs: they bond and insulate the cells, thermal barriers and electrical connections that keep the system safe and stable. Because a single cell fault can cascade, the choice of tape directly affects safety margins and throughput. Avery Dennison says the portfolio is U.S.-manufactured to meet UL® test standards and is engineered around the three challenges below.
Taming thermal runaway with Flame Tough™
The first family, Flame Tough™, uses flame-retardant acrylic- and rubber-based adhesives that let composites and barrier materials meet UL® 94 V-0 and other flammability requirements, with grades rated for continuous service up to 220 °C.
Its real value shows up in how it handles fragile thermal barriers. Mica sheets, aerogel pads and ceramic paper are the proven defenses against heat propagation, but they are brittle and shed fibers during handling. Flame Tough™ PSAs encapsulate and bond these materials so they stay intact through assembly:
- Mica sheet bonding with release liners that peel away cleanly without damaging the sheet;
- Aerogel pad encapsulation that, in independent testing, delayed thermal-propagation onset from 368 seconds to 1,294 seconds – buying precious minutes for containment and shutdown;
- Ceramic-paper mounting that traps fiber-shedding material so it cannot contaminate cell assembly.
High-voltage insulation with Volt Tough™
BESS modules routinely run above 1,000 V DC, so arcing between cells, busbars, cooling plates and housings is a constant risk. The Volt Tough™ dielectric line answers that with:
- A CTI 600 V rating (Material Group I under IEC 60112), supporting compact designs with minimal clearance;
- Dielectric strength above 200 kV/mm, verified to ASTM D149 and GB/T 1408.1-2016;
- A stable operating window of –40 °C to +150 °C;
- Insulation for cell-to-cell, busbar, and cooling-plate interfaces in high-density packs.
The tapes are built on PET constructions that balance dielectric strength, dimensional stability and cost for utility-scale use, with specialized variants addressing the CTI limits of standard polyimide films where higher temperatures are required.
Faster, cleaner assembly
Unlike liquid adhesives that need mixing, dispensing and cure time – or mechanical fasteners that add mass and stress points – the PSA tapes bond on contact. Laser die-cut parts hit ±0.1 mm accuracy for tight cell-wrapping and barrier placement, and colored variants let machine-vision systems detect placement on the line. The result is instant bonding, less waste, no VOC emissions, and direct compatibility with robotic pick-and-place.
"Avery Dennison PSA solutions help reduce flammability risks, enhance dielectric protection, and streamline design and assembly," said Max VanRaaphorst, market manager for Avery Dennison eMobility, Automotive & Energy Storage. "They let integrators raise safety margins and throughput at the same time."
What it means for the tape supply chain
As grid storage scales worldwide, the BESS segment is becoming a distinct, fast-growing pull on functional tape demand – separate from automotive and consumer electronics. Avery Dennison's move signals that tape makers are now tailoring chemistries and constructions specifically to storage safety standards rather than borrowing from EV programs. For converters and distributors, the takeaway is clear: engineered PSA solutions for thermal and electrical protection are shifting from a line item to a design-critical component in how the world stores energy.
Source: Avery Dennison Performance Tapes – "Tapes for battery energy storage systems" (official solutions page, Oct. 2026) and The Data Center Engineer / Electronic Design coverage. Original: https://tapes.averydennison.com/na/en/home/industries/battery-energy-storage-systems.html · https://thedatacenterengineer.com/?p=5077
VIP会员
