Two Japanese platforms dominate thin-bonding work in Asian electronics and appliance supply chains: Nitto's No.5600 PET series and Sekisui's 5200 PE foam series. They are often quoted against each other, yet they solve different problems. This note sets out the published numbers and the selection logic behind them.
Nitto No.5600: thin, dimensionally stable, precise
The No.5600 family uses a polyester film carrier coated with acrylic adhesive on both faces. The film gives the tape dimensional stability, so die-cut parts keep their tolerances through humidity and handling — the reason the series is standard in LCD modules, FPC fixing and nameplate work.
| Model | Thickness (mm) | 180° peel on stainless (N/20 mm) |
|---|---|---|
| No.5605 | 0.05 | 12.2 |
| No.5606 | 0.06 | 13.1 |
| No.5608 | 0.08 | 15.1 |
| No.5610 | 0.10 | 16.9 |
| No.5612 | 0.12 | 20.5 |
| No.5615 | 0.15 | 21.3 |
Data as published by Nitto Denko. Peel measured at 300 mm/min, 180°, backing PET #25. Sample values, not guaranteed limits.
Sekisui 5200: compressible, gap-filling, waterproof
The 5200 range uses a closed-cell PE foam core. Where the Nitto film tape is rigid and precise, the Sekisui foam is compliant: it absorbs tolerance stack-up, damps vibration and seals the joint against water and dust. Model numbers carry the thickness directly — 5215 is 0.15 mm, 5230 is 0.30 mm, 5260 is 0.60 mm.
| Model | Thickness (mm) | Typical use |
|---|---|---|
| 5210NAB | 0.10 | Ultra thin nameplate fixing |
| 5215PSB / 5215NAB | 0.15 | Display and bezel bonding |
| 5220PSB / 5220NAB | 0.20 | Appliance panel fixing |
| 5225PSB | 0.25 | Housing and frame sealing |
| 5230PSB | 0.30 | Waterproof sealing, IPX7 joints |
| 5235PSB / 5240PSB | 0.35 / 0.40 | Uneven surfaces, thick gaps |
| 5260PSB | 0.60 | Large gap filling, shock damping |
Thickness values as published by Sekisui. The 5200 series retains performance at 105 °C.
Choosing between them
Pick Nitto No.5600 when the bond line must be thin and dimensionally repeatable: FPC to housing, LCD sheet to frame, nameplate to a machined surface. Film carriers die-cut cleanly at high speed.
Pick Sekisui 5200 when there is a real gap to fill, vibration to damp, or water ingress to stop. Foam absorbs the tolerance you cannot machine away.
Watch the surface energy. Neither family is a low-surface-energy specialist. Untreated PP or PE needs a dedicated LSE adhesive; ask before the tooling is cut.
Pressure matters. Both are pressure-sensitive: bond strength scales with roller pressure and wet-out time. A 24 hour dwell before testing is standard practice.
Stock and converting
ShenZhen GTS Industrial Co.,Ltd stocks the Nitto No.5600 range with No.5000NS tissue tapes and Nitto masking tapes, alongside the Sekisui 5200 foam series and 5500 high heat films. Jumbo rolls are slit from 3 mm, kiss-cut gaskets and pull-tab parts are produced to drawing, and 3M and tesa equivalents ship from the same warehouse so a project can be dual-sourced.
Send the substrate pair, gap and service temperature — we will return a recommended grade with a TDS and a sample roll.
VIP会员
