Industrial tape is a low-value, high-consequence purchase: a wrong roll stops a line, and a missing document stops a container. The process below is how Liantuo closes both risks for buyers in India, Southeast Asia and the Middle East.
Shenzhen, China — Shenzhen Liantuo Industrial Tape Co., Ltd handles export orders from its base in Guangming District, Shenzhen, for overseas buyers sourcing industrial adhesive tapes. The sequence runs six steps, and each one exists because skipping it is what usually causes a dispute later.
Step 1 — Describe the application, not the part number
The first message that produces a usable answer is rarely "price for 3M 9448A". It is a short application brief:
Substrates being bonded or insulated (ABS, PP, aluminium, PCB, powder-coated steel).
Service temperature and any peak — plus whether the peak comes from soldering, a bake cycle or motor heat.
Bond area and load — a 5 mm nameplate and a 300 mm panel bracket are different problems.
Process — manual placement or automated dispensing; whether rework is required.
Format — jumbo roll, slit width or die-cut part.
With those five points, material selection and converting format are resolved together. Without them, the quotation is a price for a guess.
Step 2 — Trial a sample on the real substrate
Liantuo operates a sample service precisely because datasheet adhesion values are measured on standard test panels (typically stainless steel or a specified plastic under controlled pressure and dwell). Production substrates are not standard test panels.
A sample trial answers the questions the datasheet cannot:
| What to test | Why it matters |
|---|---|
| Initial tack on the actual surface | Low-surface-energy plastics such as PP and PE reject many adhesives outright |
| Adhesion after dwell | Some systems build strength over 24–72 hours; others peak immediately |
| Behaviour at service temperature | Adhesion drops sharply near the adhesive's softening range |
| Removal or rework | Whether the part can be lifted and re-applied without damage |
| Compatibility with the process | Varnish bake, cleaning solvent, conformal coating |
The outcome of this step is a decision: imported brand, or domestic alternative at lower cost.
Step 3 — Quotation with conversion included
Conversion is quoted together with the material, not separately. The quotation normally states the part number or material reference, the width or die geometry, quantity, unit price and lead time. Where a die has to be made for a die-cut part, that is identified as a separate line so it does not disappear into the unit price.
Step 4 — Proforma invoice (PI) and payment
The proforma invoice confirms what is being bought before production: description, quantity, unit price, total value, Incoterm, lead time and payment terms. For a first order, the PI is also the document that catches a width or format mismatch — it is much cheaper to fix on the PI than after slitting.
Step 5 — Conversion and packing
Once confirmed, material is slit or die-cut to the agreed format and packed for export. Packing decisions that matter:
Roll orientation and core support — unsupported rolls deform in transit.
Moisture protection — foil or PE bagging where humidity at destination is high.
Carton marking — part number matching the CI, so the buyer's incoming inspection can match documents to boxes.
Step 6 — CI, shipping documents and delivery
The commercial invoice (CI) is issued for the shipment, together with the packing list. Depending on the destination and the buyer's requirements, additional documents — MSDS, certificate of origin, compliance declarations — are prepared. Air freight is normal for urgent or small orders; sea freight for volume, where the tape's shelf life and storage conditions at destination should be part of the planning.
Why these six steps matter more for tape than for other consumables
Tape is cheap per roll relative to the cost of a line stoppage, which distorts purchasing behaviour toward price-only comparison. Two consequences follow:
Samples are not overhead. The cost of one sample roll is a fraction of the cost of a rejected production batch, and it is the only reliable test on a low-surface-energy substrate.
Documents are part of the product. A roll without its MSDS or compliance declaration can be stopped at customs regardless of quality, and a part number on a carton that does not match the CI creates an inspection failure that looks like a quality problem but is not.
Frequently asked questions
Is there a minimum order for a first trial?Samples are handled separately from production orders. Volume terms are confirmed at quotation, based on material and format.
Can I mix brands in one shipment?Yes. Orders commonly combine imported brands and domestic alternatives, and a single PI can cover multiple materials.
Do you supply die-cut parts for a first order, or only rolls?Die-cut parts are available, with the die identified as a separate cost item. A drawing or CAD file is needed to quote.
Which Incoterms are used?The Incoterm is stated on the PI and agreed per order, so freight and risk allocation are explicit rather than assumed.
What lead time should I plan for?Lead time depends on stock status and whether conversion or a new die is involved. It is stated on the quotation, and the PI repeats it before payment.
Who do I contact to start?Inquiries go through the company's store page at crtape.com/com/victor/, with the application brief from Step 1.
About Shenzhen Liantuo Industrial Tape Co., LtdShenzhen Liantuo Industrial Tape Co., Ltd supplies high-performance industrial adhesive tapes from Guangming District, Shenzhen, to buyers in India, Southeast Asia and the Middle East. The company distributes 3M, TESA, Nitto and Sekisui tapes plus domestic alternatives, provides slitting and die-cutting, and supports export orders with proforma and commercial invoices, samples and material selection assistance.
VIP会员
