会员登录|免费注册|忘记密码|管理入口 返回主站||保存桌面|手机浏览|联系方式
VIP   VIP会员第1年

Shenzhen Liantuo Industrial Tape Co., Ltd  
加关注0

胶带

搜索
新闻分类
联系方式


请先 登录 或 注册 后查看


站内搜索
 
荣誉资质
友情链接
  • 暂无链接
首页 > 公司新闻 > Slitting Tolerance: Why the Width You Order Is Not Always the Width You Get
公司新闻
Slitting Tolerance: Why the Width You Order Is Not Always the Width You Get
2026-11-125

A purchase order that says "25 mm slit roll" leaves three things undefined: the tolerance, what is being measured, and what happens at the edges. Each of them changes whether the roll runs on a customer's machine, and each is the source of arguments that would disappear with one line on the drawing.

What is actually measured

TermWhat it meansTypical trap
Nominal widthThe ordered figureTreated as an exact value
Tolerance bandAcceptable deviation, e.g. ±0.2 mmNot stated, so both sides assume their own
Usable widthWidth that is flat and correctly woundEdge curl means the usable width is less than the measured width
Edge conditionCut quality: clean shear vs torn or lippedA lipped edge jams narrow-track applicators

The distinction that causes most disputes is measured width versus usable width. A roll can measure 25.0 mm with a caliper and still have 24.4 mm of flat material if both edges are curled — and the customer's guide will fail on the curl, not on the width.

Where the tolerance comes from

Slitting accuracy is limited by three things: the accuracy of the slitting head, the stability of the web during the run, and the material itself. Foam and thick cloth tolerate less precision than PET film because they compress under the blade; a soft foam can drift half a millimetre within a single log roll. Paper liners move with humidity between slitting and packing, so a width measured at the machine and re-measured a week later will not always agree.

That is why a converter quotes a band rather than a number. A realistic band for filmic tapes is tighter than for foam, and both are wider than most buyers expect when they write "25 mm" on a drawing.

What to put on the purchase order

  • Nominal width and the acceptable band, stated separately

  • Whether the figure refers to measured width or usable width

  • Edge condition required, especially for narrow-track or automated application

  • Core diameter and roll length, since edge quality often degrades at the end of a log roll

  • Whether off-spec width can ship as a shorter roll rather than being rejected

Why narrow widths cost more per metre

A log roll of 1300 mm slit into 25 mm rolls yields 52 rolls only if the arithmetic is perfect. In practice the slitting plan loses material to edge trim, to the unusable edges of the master roll, and to setup between runs. Narrow widths also run slower and need more handling per metre of finished product. The price difference between 25 mm and 50 mm is therefore not double the handling — it is the yield loss on the master roll that shows up first.

How to check a delivery without a metrology lab

Measure three positions per roll — start, middle, end — with the tape still wound, using a steel rule against a flat surface. Then unroll a metre and check for edge curl by laying it on a glass or laminate surface. If the curl is visible, measure usable width instead of outside width. Record both numbers; that is the pair that predicts whether the roll will run.

What we do

We slit in-house to customer width and quote the tolerance with the price, for filmic, foam, cloth and foil constructions. Die-cut parts are quoted on drawing, and standard stock widths ship in 3 days.

Frequently asked

Can you hold ±0.1 mm on a 12 mm foam roll?
Usually not on foam — the material compresses under the blade. On PET film it is achievable; we will say which constructions can hold it before quoting.

Why is my 25 mm roll measuring 24.7 mm?
Either it is inside the quoted band, or the edge is curled and you are measuring outside width. Check curl before treating it as a width fault.

Do you accept customer-supplied master rolls for slitting?
Yes, subject to a check of liner condition and roll integrity.