会员登录|免费注册|忘记密码|管理入口 返回主站||保存桌面|手机浏览|联系方式
VIP   VIP会员第1年

Shenzhen Liantuo Industrial Tape Co., Ltd  
加关注0

胶带

搜索
新闻分类
联系方式


请先 登录 或 注册 后查看


站内搜索
 
荣誉资质
友情链接
  • 暂无链接
首页 > 公司新闻 > Tapes Inside an EV Battery Pack: Cell Wrapping, Busbar Insulation and Compression Pads
公司新闻
Tapes Inside an EV Battery Pack: Cell Wrapping, Busbar Insulation and Compression Pads
2026-11-163

A battery pack is one of the few assemblies where tape is specified by function rather than by convenience. Four jobs recur in almost every pack design, and each has a different failure mode if the wrong construction is used: cell wrapping, busbar and module insulation, compression and gap management, and thermal barrier.

The four jobs and what each demands

FunctionWhat the tape must doWhat fails if it does not
Cell / module wrappingElectrical insulation, thin, conformable, no adhesive creep at 60–80 °CChafe or insulation breach; adhesive residue on the can
Busbar insulationDielectric strength, flame resistance, withstand cell swellingCreep and eventual contact; failed dielectric test
Compression / gap pad fixingHold a foam pad in place through compression cycles without blocking itPad migration, uneven stack pressure, cell stress
Thermal barrier / flame spreadWithstand local high temperature, low thermal conductivityPropagation between modules

Cell wrapping: thin film, not masking tape

The wrap around a prismatic or cylindrical cell is an insulation layer, and it is judged by dielectric strength and by what happens to the adhesive at pack operating temperature. Standard PET film tapes are common because they are thin, dimensionally stable and available in flame-retardant grades. The failure that shows up in the field is not usually dielectric breakdown — it is adhesive creep at the overlap, where the wrap opens after thermal cycling. Overlap width and adhesive class decide this more than the film thickness.

Busbar insulation: dielectric and mechanical at once

Busbar tape has to hold voltage and survive movement. Cell swelling pushes modules outward over life, so the tape sees slow shear rather than a single load. That points to a construction with a carrier — PET or polyimide film — rather than a transfer adhesive, and to a flame-retardant grade where the pack specification calls for it. Where the busbar runs close to a sharp edge, a glass cloth or reinforced construction is often preferred over a plain film because it resists cut-through.

Compression pads: fix the pad, do not fight the stack

Compression pads are designed to deflect; the tape's job is to stop them moving during assembly, not to resist the compression. A double coated tape with a thin carrier on the pad's face, or a light foam carrier, works better here than a high-shear structural tape, because the latter resists the very deflection the pad exists to provide. The practical rule: the tape should be the weakest element in the stack in the compression direction, and the strongest in shear.

Thermal and flame barriers

Where the requirement is to slow propagation rather than to insulate electrically, the constructions change: mica-based barriers, ceramic-filled films and intumescent materials replace ordinary tapes, and the specification is written around a test rather than a data sheet. Tape in this role is usually a carrier for the barrier material rather than the barrier itself.

What buyers actually need from a supplier

  • Dielectric strength and flame rating stated per construction, not per family

  • Continuous temperature and, separately, the temperature seen during pack assembly (often higher)

  • Die-cut parts to drawing, since most pack tapes are applied as shapes rather than rolls

  • Lot traceability — pack programmes usually require it

  • Consistency of adhesive class across reorders; a silent substitution here is a safety issue, not a cost issue

What we do

We supply and convert PET, polyimide, glass cloth and flame-retardant film tapes used in pack assembly, die-cut to drawing, with lot numbers and RoHS/REACH documentation. For pack programmes we quote against the drawing and the test requirement rather than against a tape family name.

Frequently asked

Can we use a standard PET double coated tape for cell wrapping?
Only if the dielectric and temperature requirements are met and the adhesive does not creep at pack temperature. Many standard grades are not qualified for this and the substitution is usually invisible until validation.

Is thicker tape better for busbar insulation?
Not automatically. Dielectric strength per micron matters more, and a thick foam-backed tape can be worse under compression than a thin film with the right carrier.

Do you supply die-cut parts with lot traceability?
Yes, with the master roll lot carried through to the part label and the certificate.