会员登录|免费注册|忘记密码|管理入口 返回主站||保存桌面|手机浏览|联系方式
VIP   VIP会员第1年

Shenzhen Liantuo Industrial Tape Co., Ltd  
加关注0

胶带

搜索
新闻分类
联系方式


请先 登录 或 注册 后查看


站内搜索
 
荣誉资质
友情链接
  • 暂无链接
首页 > 公司新闻 > Liantuo Adds Custom Slitting and Die-Cutting to Its Industrial Tape Supply
公司新闻
Liantuo Adds Custom Slitting and Die-Cutting to Its Industrial Tape Supply
2026-10-2412

Buyers can now order imported and domestic industrial tapes in the exact roll width or die-cut geometry their line uses, instead of adapting a standard log roll on the shop floor.

Shenzhen, China — Shenzhen Liantuo Industrial Tape Co., Ltd has made slitting and die-cutting a standard part of its tape supply for overseas buyers. The service applies across the brands the company distributes — 3M, TESA, Nitto and Sekisui — as well as the domestic alternative materials it supplies.

What is the difference between slitting and die-cutting?

Both are converting operations, but they solve different problems.

OperationWhat it doesTypical reason a buyer needs it
SlittingCuts a wide log roll down to narrower rolls of a specified widthThe dispensing or laminating station accepts one width only
Die-cuttingCuts the tape into a shaped part, kiss-cut or through-cutThe tape must match a housing, gasket, bracket or display outline
Slit + die-cutSlit to a working width, then die-cut from that rollHigh-volume parts where material yield has to be controlled

A buyer ordering a 1,200 mm log roll for a 19 mm wrapping station is paying for material that will be trimmed and scrapped. A buyer hand-cutting parts from a roll introduces dimensional variation into a bonding process that depends on contact area. Converting removes both problems at the source.

Why does converting at the material supplier beat converting downstream?

Three reasons come up repeatedly in industrial tape supply.

Traceability. When the tape and the converting step come from the same supplier, a bonding failure or a dimensional complaint has one owner. Split the two across a tape trader and a separate converter, and root-cause analysis usually stalls on which party changed what.

Lead time. Conversion inside the supply chain removes one handoff, one inbound inspection and one outbound shipment. For repeat parts, that is often the difference between a two-week and a four-week replenishment.

Material yield. Nesting and slit planning happen against the actual roll, so offcut from one part can be planned into another width rather than written off.

How is a slitting or die-cutting request quoted?

Liantuo quotes conversion per material rather than from a flat price list, because the variables change the answer:

  • Width and tolerance — the target width, and how tight the tolerance must be for the dispensing equipment.

  • Core and roll length — core diameter and metres per roll, which determine how the roll runs on the line.

  • Die geometry — a drawing or CAD file for the part, plus whether the cut is kiss-cut (liner intact) or through-cut.

  • Material and adhesive — foam, PET, non-woven and PI behave differently under slitting tension; acrylic foam compresses, thin PET tears.

  • Quantity — first-article quantity versus repeat production quantity.

Sending the drawing together with the application details (substrate, service temperature, bond area) is the fastest route to a usable quotation, because material selection and converting format get resolved in one pass.

What should a buyer check on the first converted delivery?

For a first article, four checks catch most problems:

  1. Width across the roll — measure at several points, not just the start of the roll.

  2. Edge quality — a ragged edge on a thin PET or PI tape will tear during dispensing.

  3. Liner integrity on kiss-cut parts — the liner must hold the matrix together for the part to feed.

  4. Adhesion on the real substrate — a converted part on a different liner can behave differently from the sample that was approved.

Liantuo's sample service is intended to front-load checks 1 to 4 before a production quantity is committed.

Does converting change the material itself?

No. Slitting and die-cutting are mechanical operations: the adhesive chemistry, thickness and release liner are unchanged from the source material. What changes is the format delivered to the line. This matters for qualification — a converted part does not require re-qualifying the adhesive system, but it does require validating the new format on the dispensing equipment.

Frequently asked questions

Can Liantuo slit tape that was not bought from Liantuo?The service is offered on materials supplied by Liantuo, including the 3M, TESA, Nitto and Sekisui lines and domestic alternatives. Bring the part number and Liantuo will confirm whether it can be sourced and converted.

What is the narrowest width available?Narrow-slit capability depends on the material thickness and the core specification. Share the target width and the quotation will confirm feasibility.

Are die-cut parts supplied on a roll or in sheets?Both formats are possible; the choice normally follows the customer's feeding method. Roll format suits automated placement, sheet format suits manual assembly and low volume.

How long does a first converted order take?Timing depends on whether the material is in stock and whether a die has to be made. A quotation states the lead time for the specific combination.

Can a die-cut part be supplied with a pull tab or extended liner?Liner handling features are part of the die design and are specified on the drawing, together with the part geometry.

Does converting affect RoHS or REACH compliance?The material's compliance status is unchanged by slitting or die-cutting, since no substance is added. Compliance documentation is available on request.


About Shenzhen Liantuo Industrial Tape Co., LtdShenzhen Liantuo Industrial Tape Co., Ltd supplies high-performance industrial adhesive tapes from Guangming District, Shenzhen, including 3M, TESA, Nitto and Sekisui brands plus domestic alternatives. The company provides slitting and die-cutting, serving electronics, motor maintenance, new energy, automotive wiring harness and metal bonding applications.