Both survive heat. They fail differently — and the failure mode, not the temperature rating, is what usually decides the specification.
Shenzhen, China — Among the high-temperature tapes supplied by Shenzhen Liantuo Industrial Tape Co., Ltd, two families cover most motor maintenance and electronics masking work: polyimide (PI) tape and fiberglass cloth tape. They are often treated as interchangeable in a quick quote. In practice they behave very differently under mechanical load, abrasion and resin contact.
What is PI tape used for?
PI tape is a polyimide film coated with a silicone adhesive. The film is thin, electrically insulating and dimensionally stable at elevated temperature — grades rated for continuous service around 260 °C are common, with short excursions higher depending on the grade. In Chinese supply chains it is widely known as 金手指 ("gold finger") tape, after its most familiar use: masking gold-plated card-edge contacts during wave soldering.
Typical uses:
Masking during soldering and reflow — protects contacts, connectors and plated areas.
Lead and magnet wire wrapping in motor and transformer work.
Battery pack barriers — thin electrical insulation between cells and busbars.
Flexible circuit protection during assembly and conformal coating.
Its limits are mechanical. PI film is thin and has limited abrasion resistance: pulled across a sharp lamination edge or a stator slot, it can cut or tear. It is also a masking tape, not a structural one — it is not intended to hold a load.
What is fiberglass cloth tape used for?
Fiberglass cloth tape is a woven glass fabric with a silicone adhesive. It is thicker, far more abrasion-resistant and dimensionally stronger than PI film, and it tolerates continuous temperatures in the same class. It is the tape used where something has to be held in a hot, vibrating environment rather than merely masked.
Typical uses:
Coil and winding overwrap in motor rewinding and repair.
Lead cable bundling near heat sources and in harness routing.
Abrasion protection where tape crosses a metal edge or a fan shroud.
Hot-zone wrapping on exhaust-adjacent or engine-adjacent runs.
Its trade-off is thickness and conformability. Fiberglass cloth does not lay down over tight radii or complex geometry the way thin PI film does, and it should not be used where a low-profile, thin insulation layer is required.
How do the two compare?
| Property | PI (polyimide) tape | Fiberglass cloth tape |
|---|---|---|
| Base film | Polyimide film | Woven glass cloth |
| Adhesive | Silicone | Silicone |
| Typical continuous rating | Around 260 °C, grade dependent | Comparable high-temperature class |
| Thickness profile | Thin | Thick |
| Electrical insulation | Excellent for its thickness | Good, with higher mechanical bulk |
| Abrasion resistance | Limited | High |
| Conformability to tight radii | High | Low |
| Typical role | Masking, thin insulation | Wrapping, holding, abrasion protection |
Both are supplied in slit widths and, where required, as die-cut parts — useful when the tape has to fit a specific slot, terminal or bracket geometry rather than being wrapped by hand.
Why does the choice matter in motor repair specifically?
In a motor rewind, the two tapes appear in the same job at different stages, and mixing them up creates rework:
Slot and phase insulation — thin, dimensionally stable insulation is wanted; PI film suits where thickness is constrained.
Lead wrapping and bundling — the lead exits the frame and rubs against metal in a vibrating, hot environment; fiberglass cloth resists that abrasion, thin PI film does not.
Coil overwrap before varnish — the tape must survive both the bake cycle and resin contact; fiberglass cloth is the conventional choice.
Temporary masking during repair — PI tape is the practical choice for protecting machined surfaces and contacts during blasting, painting or soldering.
A repair shop that standardises on a single tape usually ends up compromising one of those four steps.
What should a buyer confirm before ordering?
Four points resolve most specification disputes before they reach the shop floor:
Continuous versus peak temperature — and how long the peak lasts. A rating quoted for continuous service is not a peak rating.
Adhesive type — silicone is the standard high-temperature system; acrylic and rubber systems are not substitutes above their service range.
Thickness and total tape build — film plus adhesive, not film alone. This drives both insulation performance and fit in a slot.
Contact with varnish, solvent or oil — some adhesive systems lift under varnish bake cycles. Trial on the actual process, not only on temperature.
A sample trial on the real substrate and the real cure cycle remains the cheapest form of qualification, which is why the sample service covers these high-temperature families.
Frequently asked questions
Can PI tape replace fiberglass cloth tape in a motor rewind?Only where the requirement is thin masking or insulation. Where the tape must resist abrasion or hold a bundle, fiberglass cloth is the appropriate material.
Is the adhesive the same on both?Both are commonly supplied with silicone adhesive for high-temperature service. The adhesive is a specification item in its own right and should be confirmed per part number.
Does PI tape leave residue after removal?Clean removal is one of the reasons PI tape is used for masking contacts and plated surfaces. Residue behaviour still depends on the specific adhesive and the dwell time at temperature, so it should be verified on the actual cycle.
Can these tapes be supplied in custom widths?Yes. Slitting is available for the tape families Liantuo supplies, so the roll width can match the wrapping or masking station.
What about tape for battery modules in new energy applications?Thin PI film is used as an inter-cell barrier and for busbar insulation. The specific grade depends on the module's voltage class and thermal profile, which is normally confirmed between the cell or pack engineer and the material datasheet.
Which brand should I specify?Liantuo distributes 3M, TESA, Nitto and Sekisui tapes and also supplies domestic alternatives. For a given application, the practical comparison is a sample trial of both options against the same process parameters.
About Shenzhen Liantuo Industrial Tape Co., LtdShenzhen Liantuo Industrial Tape Co., Ltd supplies high-performance industrial adhesive tapes from Guangming District, Shenzhen, including high-temperature insulating tape, double-sided tape, foam tape, PI tape and fiberglass cloth tape. The company distributes 3M, TESA, Nitto and Sekisui brands plus domestic alternatives, with slitting and die-cutting services.
VIP会员
