会员登录|免费注册|忘记密码|管理入口 返回主站||保存桌面|手机浏览|联系方式
VIP   VIP会员第1年

Shenzhen Liantuo Industrial Tape Co., Ltd  
加关注0

胶带

搜索
新闻分类
联系方式


请先 登录 或 注册 后查看


站内搜索
 
荣誉资质
友情链接
  • 暂无链接
首页 > 公司新闻 > PET Double Coated Tape: How Thickness, Liner and Adhesive Interact
公司新闻
PET Double Coated Tape: How Thickness, Liner and Adhesive Interact
2026-11-025

PET double coated tape looks like the simplest product a converter sells: a polyester film, adhesive on both faces, a liner. In practice most failed specifications come from treating the three parts as independent choices. They are not — changing the film thickness changes the handling, changing the liner changes what the die-cutter can do, and changing the adhesive changes what the film can carry.

The film is the mechanical backbone

The PET carrier does three jobs: it holds a fixed bond line, it resists stretch when the tape is applied under tension, and it stops the adhesive from flowing under load. A 12 µm film gives an almost invisible joint but offers little dimensional stability; a 50 µm or 100 µm film holds a gap and survives slitting and die-cutting far better. When a design moves from a 25 µm to a 100 µm construction for the same adhesive, expect the bond line to stay the same on paper but the peel performance to change, because the film no longer deflects with the substrate.

On thin metal or plastic panels the film also decides whether the joint telegraphs. A stiff carrier bridges a spot weld or a stamped rib; a thin one follows it and shows the profile through the surface.

The liner decides what the die-cutter can run

LinerBehaviour on the pressWhere it fits
Glassine / paper, thinCheapest, cuts cleanly, limited dimensional stability with humidityFlat die-cutting, short runs, hand application
PET film linerStable in humidity, holds registration, stiffer webRotary die-cutting, automated placement, thin parts
Extended liner / finger-liftAdds a handling tab, costs an extra processSmall parts picked by hand or by vacuum

The mistake we see most often is a buyer specifying a paper liner for a rotary die-cut part because it is cheaper per square metre, then discovering the liner stretches across a long web and the registration drifts. The saving disappears in the first shift.

The adhesive has to match the surface, not the tape family

A PET double coated tape is not automatically an LSE tape. Standard acrylic adheres well to metals, glass and high-surface-energy plastics; low-surface-energy grades are needed for PP, PE and powder coatings, and high-temperature grades where the part passes a bake or a solder-adjacent process. The film is identical in all three cases, which is exactly why data sheets that only say "PET double coated" are not enough to specify from.

Ask three questions of any PET construction: which adhesive on the face that touches the difficult substrate, what the total thickness without liner is, and which liner the die-cutter will run. The answers decide whether a part works, not the product family name.

What we hold

Our TESA PET range runs from thin transfer-type constructions for displays and membrane switches up to heavier carriers for nameplates and structural bonding, in standard acrylic, LSE and high-temperature adhesive systems, with paper, PET and extended liners. Each listing carries the film thickness, adhesive type and liner, so a converter can shortlist against a drawing before asking for a sample.

Frequently asked

Can I swap a 50 µm PET tape for a 100 µm one without re-testing?
No. The adhesive may be the same but the bond line, conformability and peel behaviour change. Re-test the joint, especially on thin or textured substrates.

Why does my die-cut part lift at the edge after a few weeks?
Usually the liner or the carrier, not the adhesive: a paper liner that has absorbed moisture, or a film too thin to resist the substrate's movement. Check the liner first.

Do you supply PET double coated tape die-cut to drawing?
Yes, with paper or PET liner, single or multi-layer, and with RoHS and REACH documentation for export orders.